4000FT Remote Dog Training Collar with Flash Light - User Manual
1. Important Safety Information
Note： Don't use it when your dog or collar is wet, because water conducts electricity and if you press the shock function accidentally, The level of stimulation for your dog will be greatly Increased.
CAUTION
A collar worn for too Long or made too tight on the dog, sneck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores. Risk of skin damage. Please read and follow the instructions in this manual. The proper fit of the collar is important.
 |
Never connect a leash to the product, or it will cause excessive pressure on the contacts. |
 |
Do not wear it for more than 12 hours at a time, When possible please move the collar position on the neck every 1-2 hours. |
 |
Check the fit to prevent excessive pressure； follow the instructions in this manual. |
 |
Wash the dog's neck area and contacts of the collar weekly with a damp cloth. |
 |
Please place conductive covers on the probes to protect the dog's skin. |
 |
Receiver with IP67 waterproof, it can be submerged in water up to 1 meter for up to 30 minutes, If submerged and wet, please do not use it. |
 |
If a rash or sore is found, discontinue the use of the collar until the skin has healed. If the condition persists beyond 48 hours, see your veterinarian. |
2. Quick Start Guide
Charge the devices via PC, power bank, and adapter with an output voltage of 5V for 3h.
Note: If charged with an adapter that exceeds 5V, the Receiver will deliver a rapid warning tone and stop charging automatically, and the Remote Transmitter will stop charging automatically with the indicator rapidly blinking in red.
Note: The charger, power bank and other charging devices shown in the above picture are not included in the box.
Make your dog sit down and Leave one finger space between the collar and your dog's neck. Center the contact points underneath your dog's neck, touching the skin.
Turn on the Remote and Receiver, the Receiver's green LED Indicator Light now continues to blink regularly.
Warning Tone Command: Press the Warning Tone Button, green light lights up rapidly on the Remote. The Receiver will deliver a warning tone, and the green LED Indicator Light on the Receiver comes up simultaneously.
Note: Press down the knob then turn the knob to adjust the Warning Tone level. and finally, press the Warning Tone Button to confirm the modification.
Vibration Command: Press the Vibration Button, green light lights up rapidly on the Remote. The Receiver will deliver vibration, and the green LED Indicator light on the Receiver comes up simultaneously.
Note： Press down the knob then turn the knob to adjust the Vibration Level, and finally, press the Vibration Button to confirm the modification.
Shock Command: Press the Shock Button, and the red light lights up rapidly on the Remote. The Receiver will deliver a shock, and the green LED Indicator light on the Receiver comes up simultaneously.
Note： Press down the knob then turn the knob to adjust the Shock level, and finally, press the Shock Button to confirm the modification.
Switch the channel by pressing the On/Off (Channel) Button. This product can train up to 2 dogs.
How to pair up the second receiver?
1 Turn on the remote control and press the 1/2 button to switch to mode 2, and Turn on the second receiver.
2.Press the power button on the receiver 3 times, you will hear a beeping tone.
3.Press the warning tone button on the remote transmitter the receiver will beep 3 times, then the pairing process is completed.
3. Training Tip
HOW to find the best stimulation for your dog?
Important: Always start at the lowest level and increases stimulus levels gradually The Remote Training Collar has 8 types of Warning Tones, 16 levels of vibration, and 99 levels of shock.
Stimulation level best for your dog： A slight change in your dog's behavior, such as looking around in curiosity, scratching a collar, or flicking his ears, indicates the Recognition Level that is best for your dog.
Important notes：
- When testing beep and vibration, you can increase the level one by one. When testing shock function, you can increase up to 5 levels at a time. Do not increase the level in a large span to prevent the dog from being frightened.
2.lf your dog should not vocalize or panic when receiving stimulation, the stimulation level is too high for your dog, please go back to the previous level and repeat the process.
3.When there is no response for the first time, please repeat 3 times to observe the dog's reaction, and then consider increasing the stimulation level.
4.If your dog continues to show no response at the highest Level of Vibration or Static Shock, check the fit of the Receiver. If your dog has long or thick hair, contact our Customer Care Center to obtain a longer set of Contact Points. Then go back to #1 and repeat the process.
If this still does not yield any results, your dog's hair will need to be trimmed around the Contact Points.
Please note that based on 300 000+ sold units 97% Satisfaction Rate means less than a 3% failure due to the dog's natural traits. If after completing all of these steps, your dog still does not indicate that he is feeling the stimulation, please contact our customer service.
How to Maximize the distance?
Terrain, weather, vegetation, transmission from other radio devices, and other factors will affect the maximum range.
Hold the Remote Transmitter in a horizontal position away from your body to achieve optimum range. For maximum signal strength, keep the device properly charged.
*Avoid touching the antenna or the range may decrease substantially
4.Product Overview
Note：
- The icon "88” will be displayed when the Remote Transmitter toggles to the lock state.
- The Remote Transmitter will go into a sleep mode if no operation in one minute.
Note:
- With the Receiver and the Remote Transmitter on and successfully paired up, the Receiver Battery icon will be displayed when pressing any of the Function Buttons.
- lf the Receiver is turned off, the Receiver Battery will keep displaying its level before shutdown on the Remote Transmitter.
How the System Works
The Remote Training Collar is easy to use with an advanced digital display that tells you exactly what level of stimulation you are using.
The Remote Training Collar assists you in controlling your dog without a leash.
At the push of a button, your Remote Transmitter sends a signal activating your dog's Receiver. He receives a safe but annoying stimulation. He'll quickly learn the association between his behavior and your correction; in no time, you'll have a better -behaved dog. The Remote Training Collar has been proven safe, comfortable, and effective for both small and large dog breeds. Using the Remote Training Collar consistently and correctly, any basic obedience commands can be taught and will help to correct many misbehaviors that your dog exhibits.
5.Training Modes
1.Warning Tone Mode
Press the Warning Tone Button and the Receiver will deliver a warning tone. It will cut off automatically if you press and hold the Warning Tone Button for 10 seconds. There is a total of 8 levels of Warning Tone.
To adjust the warning tone level, press the Adjustment Knob to select the Warning Tone Mode first, then turn the Adjustment Knob left and right to raise/Lower to the desired level, and finally press any button 
to confirm the modification.
2.VIbratIon Mode
Press the Vibration Button and the Receiver will deliver a vibration. It will cut off automatically if you press and hold the Vibration Button for 10 seconds. There is a total of 16 Levels of Vibration.
To adjust the vibration level, press the Adjustment Knob to select the Vibration Mode first, then turn the Adjustment Knob left and right to raise/lower to the desired level, and finally press any button to confirm the modification.
3.Shock Mode
Press the Shock Button and the Receiver will deliver a static shock. It will cut off automatically if you press and hold the Shock Button for 10 seconds. There is a total of 99 levels of Shock.
To adjust the shock level, press the Adjustment Knob to select the Shock Mode first, then turn the Adjustment Knob left and right to raise/lower to the desired level, and finally press any button to confirm the modification.
When testing the Shock function for the first time, place the Test Bulb Kit on the Contact Points. The Test Bulb Kit lights up to indicate that the Shock function is working, and it will become brighter at higher shock levels.
Two Light Mode： L1 for the Illuminating Light Mode, L2 for the Positioning Light Mode, Press the Light mode to switch.
Illuminating Light Mode: Press the Light Button, and the Illuminating Light up on the Receiver, while the remote shows the light icon.
Press the Light Button again, and the Illuminating Light Mode will be off. Once the Illuminating Light is on, it will cut off automatically after 30 minutes if there is no operation on the Remote Transmitter.
The Positioning Light Mode： Press and hold the Light Button, and the LED Light blinks rapidly in blue, white, and red, while the "L2” icon is shown on the Remote Transmitter. Press and hold the Light Button again, and the Positioning Light Mode will be off. Once the Positioning Light is on, it will cut off automatically after 30 minutes if there is no operation on the Remote Transmitter.
Note:
Once both of the Light Modes are active, the green Indicator on the Receiver lights up if any other three training operations. After the operation is over, the Indicator Light resumes to the Light Mode you set.
5.Switching Channels
Press the On/Off (Channel) Button to choose the Receiver you want to control if you have paired up two Receivers.
Note：
The Remote Transmitter will go into the sleep mode if no operation in one minute saving battery power.
6.Fitting the Receiver
IMPORTANT:
The proper fit and placement of your Receiver are important for effective training. The Contact Points with Conductive Silicone Cover must have direct contact with your dog's skin on the underside of his neck. To assure a proper fit, please follow these steps:
- Make sure that the Receiver is turned off.
- Let your dog stand on four feet or lay down fully (A).
- Place the Receiver on your dog's neck close to the ears. Center the Contact Points underneath your dog's neck, touching the skin (B).
Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that contact is consistent.
- The Receiver should fit snugly, yet loose enough to allow one finger to fit between the strap and your dog's neck (C).
-
Allow your dog to wear the collar for several minutes then recheck the fit. Check the fit again as your dog becomes more comfortable with the Receiver.
-
How to adjust the length of the collar?
CAUTION:
Risk of Skin Damage. Too Long time or too tightly fitting may cause pressure necroses, which are often misidentified as burns. Please follow the below instructions:
Do not shave the dog's neck as this may increase the risk of skin irritation.
Do not Leave the Receiver on your dog's neck for continuous 12 hours.
Never attach a Leash to the collar.
Never fit the Receiver too tight to your dog's neck.
6.Pairing Up
If you feel the Receiver is not responding to the Remote Transmitter, follow the following steps to pair them up.
1.Turn on the remote control and press the 1/2 button to switch to mode 1or2f and Turn on the second receiver.
2.Press the power button on the receiver 3 times, you will hear a beeping tone.
3.Press the warning tone button on the remote transmitter the receiver will beep 3 times, then the pairing process is completed.
Tips: The Receiver is paired up to the Remote Transmitter in Channel 1 by factory default setting. If you buy a new Receiver, you can follow the above instruction to pair it up to Channel 2. The system can pair up to 2 Receivers in 2 different channels. If you cannot pair your device successfully, it may be due to signal interference. Please try pairing again in a different Location or contact our service center.
7.LCD Display & Indicator Definitions
Frequently Asked Questions
Q: Is the Stimulation safe for my dog?
A： While the Stimulation is unpleasant, it is harmless to your dog. Electronic training devices require interaction and training from the owner to achieve desired results.
Q: How old does my dog have to be before using the Remote Training Collar?
A： Your dog should be able to recognize basic obedience commands such as "Sit" or “Stay". Dogs should be at least 6 months old before using the Trainer.
Q： Once my dog is trained and has been obeying my commands, will he have to continue to wear the Receiver?
A： Probably not. You may need to reinforce training with the Receiver from time to time.
Q:ls the Receiver waterproof?
A: Yes. The Receiver meets IP67 waterproof rating, but make sure to keep the area dry when charging.
Note: the Remote Transmitter is not waterproof.
Q:Will I get a maximum range with the Remote Training Collar?
A:The range of the Remote Training Collar will vary according to terrain, weather, vegetation, as well as transmission from other radio devices. See HHow to Maximize the Distance0 on page 17 for tips on maximizing your range.
Q：How long can I continuously deliver stimulation to my dog?
A:The maximum amount of time you can press the Warning Tone /Vibration/Shock button and deliver stimulation to your dog continuously is 10 seconds. After this, the Remote Transmitter will time out, and these stimulation buttons must be released and pressed again.
Trouble Shooting
1.My dog does not respond when I press a button.
Make sure the Receiver has been turned on.
If your range has reduced from the first time you used the Remote Training Collar, the battery may be low in either the Remote Transmitter or the Receiver.
Many factors can impact the amount of range you have with the Remote Trainer. For a list of these factors, see "How to Maximize the Distance'1 on page 17.
Test the Receiver with the Test Bulb Tool.
- Turn the Receiver on.
- Hold the Test Bulb Tool to the Contact Points on the Receiver.
- Press the Shock Button on the Remote Transmitter.
- The Test Light will flash. At higher shock levels, the Test Bulb Tool will flash brighter.
NOTE: If the Test Bulb Tool does not flash, recharge the Receiver and re-test. If the Test Bulb Tool still does not flash, contact our Customer Care Center.
Increase the Stimulation Level. Refer to "HOW to find the best stimulation for your dog?" on page 16 for more information.
Make sure the Receiver's Contact Points are placed snugly against your dog's skin. Refer to “Fitting the Receiver" on page 13 for more information.
2.The Receiver will not turn on.
Make sure the Receiver has been charged. For the initial charge, be sure to charge it for 4 hours. Subsequent charges only take 2~ 3 hours.
3.The Receiver is not responding to the Remote Transmitter.
- Verify the Receiver is on.
- If the indicator is blinking rapidly, fully charge the Receiver.
- If the above two solutions did not resolve the problem, please refer to “VIII. Pairing Up" on page 14 to re-pair the Receiver to the Remote Transmitter.
FCC Statement
USA
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the Limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.